Made in China
Analog Circuits Synthetic Experimental System China Engineering Lab Training System Suppliers
The for the experiments covering the course of analog electronics technology which addresses the requirements of colleges or vocational schools.
DC power supply: -5V~+5V.
AC power supply: 0V, 6V, 10V, 14V, 17V with the function of short circuit protection
and auto recovering.
Relay, speaker, buzzer, oscillating coil, controllable silicon, 12V signal lamp, power
resistor, rectifier bridge, diodes, integrated three-terminal voltage regulator, capacitor,
transistors, buttons and potentiometers are provided.
Experiment modules including: Voltage amplifier circuit, Integrated operational
amplifiers, power amplifier, DC stabilized power supply, FET amplifier & differential
amplifier, controllable thyristor rectifier circuit, common electronic devices.
Experiment boards can be fixed by the 4 blue sockets
DIP IC sockets(1 14P, 2 8P) and sockets for components connection provided.
LAB EXERCISES
Transistor common emitter amplifier
FET amplifier
Negative feedback amplifier
Emitter follower
Differential amplifier
Specification measurement of integrated op amp
Basic application of integrated op ampI - analog operational circuit
Basic application of integrated op ampII - signal processing (active filter)
Basic application of integrated op ampIII - signal processing(voltage comparator)
Basic application on integrated op ampIV - signal processing(waveform generator)
RC sine wave oscillator
LC sine wave oscillator
Assemble and commissioning of function signal generator
VCO(voltage controlled oscillator)
LF power amplifier I-OTL power amplifier
LF power amplifier II - integrated power amplifier
DC stabilized power supply I - series transistor stabilized power supply
DC stabilized power supply II - integrated voltage regulator
Controllable thyristor rectifier circuit
Synthetic experiment - design and commissioning of multimeter
|
DC power supply |
±5V/1A and ±12V/1A with the function of short circuit protection and auto recovering for each circuit. |
|
|
Function signal generator |
Output waveform: sine wave, square wave and triangle wave Amplitude ranges: 0~16VP-P. Frequency ranges: 2Hz~2MHz(switched into seven ranges) Switched attenuation: 0dB, 20dB, 40dB and 60dB(two buttons) |
|
|
Frequency meter |
Measuring range: 1Hz~10MHz with 6-digit common-cathode LED display. Strobe time: 1s. Sensitivity: 35mV@1-500kHz/ 100mV@500kHz-10MHz The Frequency indicator can be used for measurements of external signal as well |
|
|
RMS AC digital millivoltmeter |
Measuring range: 0.2mV~600V(RMS value) @ 10Hz~1.5MHz. It is used to measure the RMS value of sine wave, triangle wave and narrow pulse. |
|
|
20M Two-channel oscilloscope |
1) Deflection coefficient: 5mV/DIV-5V/DIV 2) Vertical mode: CH1, CH2, ALT, CHOP, ADD |
|
|
3 and 1/2 digital multimeter |
1) DC voltage: 200mV/2V/20V/200V/1000V ±(0.5%+3) 2) AC voltage: 2V/20V/200V/750V ±(0.8%+5) 3) DC current: 20uA/2mA/200mA/20A ±(1.5%+3) 4) AC current: 2mA/20mA/20A ±(1.5%+5) 5) Resistance: 200Ω/2kΩ/20kΩ/200kΩ/2MΩ/20MΩ ±(0.8%+5) 6) Conductance: (0.1-100)nS ±(1.0%+30) 7) Capacitance: 20nF/200nF/20uF/200uF ±(4.0%+10) 8) Frequency meter: 20kHz ±(1.5%+25) Celsius temperature: -40oC-1000oC ±(0.75%+3) 9) Special function: diode test, transistor test, ON/OFF alarm, low-voltage display, data hold, turn off the power automatically etc. Input impedance: 10MΩ, sampling rate: 3 times/s, AC frequency response: 40-400Hz, operation mode: manual. Maximum range: 1999. |
|
|
Configuration: |
||
|
DC stabilized power supply: |
1 |
|
|
Function generator: |
1 |
|
|
Frequency meter: |
1 |
|
|
RMS AC digital millivoltmeter: |
1 |
|
|
20M Two-channel oscilloscope: |
1 |
|
|
3 and 1/2 digital multimeter: |
1 |
|
|
MF500 Pointer type multimeter: |
1 |
|
|
Accessories & connection leads: |
1 set |
|
|
Operating instructions and laboratory manual: |
1 set |
|
As leading analog circuits synthetic experimental system manufacturers, suppliers & exporters in China, Engineering Lab China combines factory-direct pricing, strict quality control and reliable worldwide shipping. Every Analog Circuits Synthetic Experimental System is built in-house in Guangzhou City to deliver dependable performance for engineering training and teaching environments.
We manufacture every Analog Circuits Synthetic Experimental System at our own facility in Guangzhou, China. No middlemen — you get factory pricing on Engineering Laboratory Trainer Kits, Training Charts and Educational Equipment.
Every Analog Circuits Synthetic Experimental System passes a strict outward quality check before dispatch, so it stands up to daily use in Industrial Training Institutions, Engineering Colleges & Polytechnics.
From a single trainer kit to a full lab tender, our team manages packaging and prompt international delivery so your Analog Circuits Synthetic Experimental System arrives on schedule, anywhere in the world.
EngineeringLabChina is a leading analog circuits synthetic experimental system manufacturers, analog circuits synthetic experimental system suppliers & exporters in China. Whether you need a single unit for a lab refresh or a complete tender for a polytechnic, we handle Engineering, Procurement, Installation and Commissioning under one roof.
We accept Wire or Telegraphic Transfer / Letter of Credit. Shipping is based on consignment size — contact us with your requirement for an accurate quote.
Share quantity, destination country and any custom specs for the Analog Circuits Synthetic Experimental System.
Our team replies with factory pricing, lead time and shipping options within 24 hours.
We manufacture in Guangzhou, run a quality check and prepare export-ready packaging.
Consignment dispatched by your preferred mode — sea, air or courier — to your door.
Full product category index — manufactured in Guangzhou, exported worldwide.
