Made in China
Fundamentals of Electronics Experimental System China Engineering Lab Training System Suppliers
This equipment is designed for experiments covering course of analog electronics, which addresses the requirements of colleges or vocational schools.
DC signal source: two-way of -5V~+5V adjustable power supplies
AC power supply: 0V, 6V, 10V, 14V and 17V AC power supply (AC 50Hz), with the function of short-circuit protection & auto-recovery is provided for each circuit.
Components: relay, loudspeaker, buzzer, oscillating coil, 12V signal lamp, power resistor, rectifier bridge, diode, 3-terminal voltage regulators, capacitors, triodes, pushbuttons and potentiometers etc.
The experimental modules can be fixed by the four blue sockets (flexible) (which have already installed on the board).
The experimental modules including: single transistor/feedback amplifier, emitter follower, oscillator with RC series/parallel network, differential amplifier and LF OTL power amplifier.
DIP IC sockets and sockets for components connection are provided.
Lab exercises
Transistor common emitter amplifier
FET amplifier
Negative feedback amplifier
Emitter follower
Differential amplifier
Specification measurement of integrated op amp
Basic application of integrated op amp I-analog operational circuit
Basic application of integrated op amp II-signal processing (active filter)
Basic application of integrated op amp III-signal processing(voltage comparator)
Basic application on integrated op amp IV-signal processing(waveform generator)
RC sine wave oscillator
LC sine wave oscillator
Assemble and commissioning of function generator
VCO(voltage controlled oscillator)
LF power amplifier I-OTL power amplifier
LF power amplifier II- integrated power amplifier
DC stabilized power supply I-series transistor stabilized power supply
DC stabilized power supply II-integrated voltage regulator
Controllable thyristor rectifier circuit
Synthetic experiment-design and commissioning of multimeter
|
DC stabilized power supply |
Two-way ±5V@1A and two-way ±12V@1A with short-circuit soft cutoff protection and auto recovery function is provided for each circuit. |
|
Function generator |
1. Frequency range: 2Hz~2MHz is stepped into 7 ranges 2. Output waveform: sine wave, square wave and triangle wave. 3. Output amplitude: 0~16VP-P 4. Output attenuation: 0dB, 20dB, 40dB, 60dB. |
|
Frequency meter |
1. 6-bit LED display 2. Frequency range: 1Hz~10MHz 3. Sensitivity: 35mV(1-500kHz)// 100mV(500kHz-10MHz) 4. It is available to monitor the output frequency of function signal generator and measure the frequency of input signal. |
|
RMS value AC digital millivoltmeter |
It is available to measure the RMS value of sine wave, triangle wave and narrow pulse. Measuring range: 0.2mV~600V(RMS value) Frequency range: 10Hz~1.5MHz Accuracy: ±0.5%±2 digit |
|
20M two-channel analog oscilloscope |
1. Deflection factor: 5mV/DIV-5V/DIV overlapping in 10 ranges 2. Vertical mode: CH1, CH2, ALT, CHOP, ADD |
|
-digit digital multimeter |
1. DC voltage: 200mV/2V/20V/200V/1000V ±(0.5%+3) 2. AC voltage: 2V/20V/200V/750V ±(0.8%+5) 3. DC current: 20uA/2mA/200mA/20A ±(1.5%+3) 4. AC current: 2mA/20mA/20A ±(1.5%+5) 5. Resistance: 200Ω/2kΩ/20kΩ/200kΩ/2MΩ/20MΩ ±(0.8%+5) 6. Conductance: (0.1-100)nS ±(1.0%+30) 7. Capacitance: 20nF/200nF/20uF/200uF ±(4.0%+10) 8. Frequency: 20kHz ±(1.5%+25) temperature: -40oC-1000oC ±(0.75%+3) 9. Special function: diode test, triode test, on/off alarm, low-voltage display, data hold, self-turning off, functional protection, self-recovery insurance, shockproof, 10MΩ input impedance, 3 times/s sample rate, 40-400Hz AC frequency response, manual operation and the maximum display is 1999. |
|
Analog multimeter |
DC voltage: DCV 0/2.5/10/50/250/500/2500V DC current: DCA 0/50UA/1/10/100/500MA AC voltage: ACV 0/10/50/250/500/2500V Resistance: Ω R×1 R×10 R×100 R×1K R×10KΩ |
As leading fundamentals of electronics experimental system manufacturers, suppliers & exporters in China, Engineering Lab China combines factory-direct pricing, strict quality control and reliable worldwide shipping. Every Fundamentals of Electronics Experimental System is built in-house in Guangzhou City to deliver dependable performance for engineering training and teaching environments.
We manufacture every Fundamentals of Electronics Experimental System at our own facility in Guangzhou, China. No middlemen — you get factory pricing on Engineering Laboratory Trainer Kits, Training Charts and Educational Equipment.
Every Fundamentals of Electronics Experimental System passes a strict outward quality check before dispatch, so it stands up to daily use in Industrial Training Institutions, Engineering Colleges & Polytechnics.
From a single trainer kit to a full lab tender, our team manages packaging and prompt international delivery so your Fundamentals of Electronics Experimental System arrives on schedule, anywhere in the world.
EngineeringLabChina is a leading fundamentals of electronics experimental system manufacturers, fundamentals of electronics experimental system suppliers & exporters in China. Whether you need a single unit for a lab refresh or a complete tender for a polytechnic, we handle Engineering, Procurement, Installation and Commissioning under one roof.
We accept Wire or Telegraphic Transfer / Letter of Credit. Shipping is based on consignment size — contact us with your requirement for an accurate quote.
Share quantity, destination country and any custom specs for the Fundamentals of Electronics Experimental System.
Our team replies with factory pricing, lead time and shipping options within 24 hours.
We manufacture in Guangzhou, run a quality check and prepare export-ready packaging.
Consignment dispatched by your preferred mode — sea, air or courier — to your door.
Full product category index — manufactured in Guangzhou, exported worldwide.
